Q: I want bumper protection that works, is stylish, and doesn't look like a mat or pad
hanging over my bumper. How noticeable is your product on the bumper?
A: 4Bumpers® has a sleek appearance and most passersby won't even notice it on your
vehicle.
..............................................................................................................................................
Q: Does your product protect front and rear bumpers?
A: Yes, 4Bumpers® can protect both front and rear bumpers from those annoying dings and
scratches. It attaches to almost all cars on the front bumper. In the rear, the license plate
must be in the bumper area in order to use 4Bumpers®.
..............................................................................................................................................
Q: Will 4Bumpers damage the other car?
A: The 4Bumpers® rounded edge is encased in rubber. Regardless if you come into contact
with the other vehicle or vice versa, the rubber edge should prevent damage to the other
vehicle as well as to your 4Bumpers® powder coated finish. Over time the rubber edge
may become marred and replaceable rubber edges are available on the Order page.
..............................................................................................................................................
Q: I currently have a device that requires me to install it every time I park and remove it when
I am ready to drive. It takes up space in my trunk and because it is exposed to the outdoor
elements and other cars, it gets very dirty and as a result is not something I like touching
the other contents of my trunk. I also don’t look forward to handling it each and every time
I want to drive. I even sometimes forget and drive with it still on the back of my car. How
is your product different?
A: Our product has a simple and quick one-time installation. 4Bumpers® remains on the
exterior of your vehicle 24/7 and requires no additional handling (a real benefit during rainy
or snowy weather).
..............................................................................................................................................
Q: I have a rear-engine vehicle-will your product fit my vehicle?
A: Yes, as long as your license plate is in the bumper area you will get all the benefits that 4Bumpers® has to offer.
..............................................................................................................................................
Q: Will 4Bumpers protect my car bumpers in non-parking type accidents?
A: Although 4Bumpers® is made from solid steel, it was designed solely to prevent dings and
scratches to bumpers during low speed parallel parking incidents. It was not designed to
protect against property damage that occurs from accidents.
..............................................................................................................................................
Q: I was just ticketed because my rubber bumper protector completely covered over my
license plate. Will 4Bumpers also cover over my license plate?
A: No.
..............................................................................................................................................
Q: Do I have to remove 4Bumpers before I get in the car to drive away?
A: No. 4Bumpers® needs to be installed just one time. Afterward, it will remain on your car
24/7 providing protection without you having to do anything further. This also means it
wont take up extra space in your trunk like other guards.
..............................................................................................................................................
Q: Will 4Bumpers protect my car bumper if I hit another car while I am parallel parking?
A: With 4Bumpers® 24/7 protection on your vehicle, unintentional or accidental bumper
contact caused by you or the other driver makes no difference – you will be protected
without remembering to put on a pad or flip-out a mat.
..............................................................................................................................................
Q: Many other devices have very serious warnings or disclaimers about the dangers involved
in using their products because they can cover exhaust pipes and cause serious harm or
death-does your product cover the exhaust pipes?
A: No, our product is made from solid steel, attaches at the license plate area and will not
cover over or even touch your exhaust system.
..............................................................................................................................................
Q: How do I know whether to install 4Bumpers with the rounded guard in the upper or lower
position?
A: See Installation Page. If you have any doubt about which of the two positions
4Bumpers® can be installed, please call us and a representative can further assist you.
..............................................................................................................................................
Q: Does your product require the use of straps or velcro?
A: No. And, depending upon the length of your existing license plate screws, most of the time
the same 2 or 4 screws can be reused to attach 4Bumpers® to your vehicle bumper.
..............................................................................................................................................
Q: Can 4Bumpers bend?
A: 4Bumpers® is highly resilient as you can see from our videos. However, a strong enough
impact may cause it to bend and yet still achieve its purpose to protect your bumpers.
..............................................................................................................................................
Q: Do you sell additional rubber edging for the front of the guard.
A: Yes. You can order it from our website.
..............................................................................................................................................
Q: My license plate is located at the trunk level in the rear of my car. Can I use your product?
A: No. The unit would be situated too high in the trunk to protect your bumper.
..............................................................................................................................................
Q: What kind of paint is used to protect the metal?
A: All 4Bumpers® units are powder coated with a 5-step process providing great protection
from outdoor elements.
..............................................................................................................................................
Q: Is 4Bumpers actually made in the USA?
A: Yes. The idea for 4Bumpers® was born in the USA. Later, it was awarded a US Patent as
well as a US registered trademark. All the steel used in 4Bumpers® was manufactured in
the USA . . . all factories used to fabricate 4Bumpers® are located in the USA . . . our
powder coaters are located in the USA . . . and our silk screeners are also located in the
USA. So, yes, we proudly say that 4Bumpers® is actually Made in the USA.
Back to top
|
